N1201SA 137.5MHz - 2.7GHz UV RF Vector Impedance ANT SWR Antenna Analyzer Meter

Description

N1201SA UV RF Vector Impedance ANT SWR Antenna Analyzer Meter Tester
137.5MHz - 2.7GHz
English verison with
Enlish instructions
N1201SA
working currency  137.5MHz~2700MHz
stepped frequency  1kHz
Display  2.4cun TFT trdp
resolution ratio 320*240(QVGA)
2000mAH(7.4Wh)
power consumption <1.5W
charge current 400mA
charge port USB
Auto power off can be set 5-60minutes
measured parameters  resistence  reactance  standing wave s11
resolution ratio 4 number
frequency accuracy about 5ppm
Connector SMA-K
measurement range:
impedance:0.1~1000
standing wave:1.000~65
s11(dB):0dB~-60dB
Working temperature:0~40 degree
atmospheric pressure:860hPa~1060hPa
Description：
This instrument  has  four interfaces: single point measurement, scanning, system information, correction and calibration
The default boot into single-point measurement interface.
Note: For the convenience of the user, each time calibration correction options will automatically change to the user calibration. Meanwhile, in order to ensure the integrity of the calibration, the calibration process, the automatic shutdown function fails, the consistent boot.
Startup and shutdown
Hold down the CTRL key off press the power switch button.
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
The boot state, long press (2S above) the switch button, after the release, the instrument will shut down
Recommend the use
1, in order to ensure the accuracy of measurement and calibration, preheat the instrument at least 15 minutes.
2, try to use good quality RF cable and connectors.
3, calibrated cable marked to the next may not need to calibrate and direct use.
4, test cable process affect the measurement accuracy, it is recommended that, where possible, do not choose too long test cable.
5, measurement and calibration before, make sure you are not in a strong wireless signal, so as to avoid interference caused by inaccurate measurements.
6, if the impedance measurements themselves do not understand, you can refer to a vector network analyzer instructions and tutorials. This instrument is equivalent to a single-port vector network analysis.
Shipping
Item will be shipped out within 2 business days after receipt of your payment, we ship the item through hongkong Air mail or China Post.          We Ship to Worldwide, but Italy, Nigeria, Brazil will take long delivery time .
Before buying, Please make sure your address is correct. Or not, please correct it before payment
Ship to worldwide from Hong Kong within 12-24 hours after payment completed received, and will give you the tracking number asap. sometimes we will send it by flat post air mail if just one low price order.Hope you understand.
we advise shipping by DHL or EMS,and we have gave a discount for you,you can received it in 4-9 business days.
it takes about 15-30days usually if shipping by CHina/Hong Kong post air mail
Payment
We ONLY accept payment by Paypal.
All payments must be received within 7 working days after auction has ended. Non-paying bidders will be reported to ebay.
Feedback
If you have any questions or comments about our products or policies, please contact us by emails with your purchased item number.
You also can contact us by leaving us an eBay message,we will be responded within 24hours.
Customer satisfactory is most important to us. If you have a problem or question regarding your transaction please contact us before leaving any type of feedback.
Negative feedback does not solve anything. We are always willing to work things out, thank you!
Return Policy
Refunds are only offered for defective products reported within 7 days upon receipt
Buyers need to return the defective item for the replacement at his own cost. Item must be returned by registered airmail to our requested address.
We do our best to serve each and every customer the best we can.
if you need more items,we can provide you a wholesales price,you can contact us by message or email.